Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Engine major repairs
      3.4.1. An engine electric equipment
      3.4.2. The ignition distributor
      + 3.4.3. The generator
      3.4.4. The battery
      3.4.5. A starter
      3.4.6. The traction relay of a starter
      3.4.7. Gauges
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      - 3.4.11. Removal and engine installation
         3.4.11.1. The engine of 2,6 l
         3.4.11.2. 12-klapannyj the engine of 3,0 l
         3.4.11.3. 24-klapannyj the engine of 3,0 l
         3.4.11.4. The engine of 3,5 l
      3.4.12. A cover of a head of the block of cylinders
      + 3.4.13. Platens and коромысла
      3.4.14. The thermostat of system of cooling
      3.4.15. An inlet collector
      3.4.16. A final collector
      3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Турбокомпрессор
      3.4.19. Турбонагнетатель
      3.4.20. A radiator
      3.4.21. Маслоохладитель
      3.4.22. The fan
      3.4.23. The pump of a cooling liquid
      + 3.4.24. A head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. A gear belt and covers
      3.4.30. A chain and a cover (the engine 2,6)
      3.4.31. The oil pallet
      3.4.32. The oil pump and sajlent-platens (виброгасители)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. A back epiploon
      3.4.37. Radical bearings
      3.4.38. A flywheel
      + 3.4.39. An exhaust system
   + 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes

3.4.11.2. 12-klapannyj the engine of 3,0 l

THE GENERAL DATA

REMOVAL ORDER 12-KLAPANNOGO THE ENGINE OF 3,0 L

Disconnected units, hoses and wires at dismantle 12-klapannogo the engine of 3,0 l

14. A generator socket
15. The coil of ignition and the power switching block
16. A socket of the electric motor of the air proof-reader of idling
17. A gauge socket заслонки
18. A socket of the gauge of temperature for the conditioner
19. A socket of the gauge of temperature of a liquid of a control system of the engine

20. A socket of the gauge of the index of temperature of a liquid
21. A joint of a vacuum hose отсоса exhaust gases
22, 25, 28. The tyre of connection with weight
23. A hose of the amplifier of brakes
24. Burn down control systems of the engine
26. The gauge of temperature of system рециркуляции
27. A socket of the gauge of pressure of oil
29. A guard
30. A bolt of a support of the engine

Removal

PERFORMANCE ORDER

1. Remove a cowl.
2. Lift the car and remove engine guards.
3. Execute декомпрессию. For this purpose disconnect a socket in a back part of a fuel tank, start the engine and after its stop switch off ignition.
4. Disconnect weight.
5. Merge a liquid from cooling system. Merge oil from transmission and the engine.
6. Disconnect on the engine hoses of a radiator and other hoses of system of cooling.
7. Remove a radiator.
8. Remove a fan casing.
9. Disconnect from a collector an exhaust pipe.
10. Remove transmission (subsection 9.3.6 see).
11. Remove an air line of the air filter.
12. Disconnect a cable throttle заслонки.
13. Disconnect wires from the conditioner.
14. Remove the conditioner, not disconnecting from a highway, take aside and fix.
15. Remove the pump of the hydraulic booster and take aside, not disconnecting from a highway.
16. Disconnect a cruise-control hose (if it is provided).
17. Disconnect fuel hoses (having begun with a hose of the raised pressure with which before a detachment cover with rags), disconnect a vacuum hose of fuel system.
18. Remove the gauge throttle заслонки, the ignition coil, the block of the power transistor, the gauge of temperature of system рециркуляции, all gauges of temperature of a liquid, the gauge of pressure of oil, the generator and thermoswitches.
19. Remove wires of connection of the engine with weight.
20. Disconnect a vacuum hose отсоса exhaust gases and a hose of the amplifier of brakes.
21. Disconnect a socket from the electric motor of the air proof-reader of idling.
22. Disconnect other wires.
	23. Attach таль the lift and will hang out the engine.
24. Remove guards of support of the engine and turn away bolts of fastening of support of the engine to a frame.
25. Cautiously lift the engine and get from a motor compartment. Establish the engine on supports (not on the pallet).

Installation

PERFORMANCE ORDER

Engine installation is carried out upside-down. First of all establish the engine, turn bolts of support and tighten them with the moment 30–40 Н.м. Replace a lining of an exhaust pipe on a collector and fastening bolts, and also a sealing ring of a gasoline pipe line. Bolts of fastening of a radiator tighten with the moment 8–11 Н.м. Fill in a liquid, oil and start the engine. After warming up restore levels of liquids. Repeatedly adjust a cable, belts, idling and ignition.