Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Engine major repairs
3.4.1. An engine electric equipment
3.4.2. The ignition distributor
+ 3.4.3. The generator
3.4.4. The battery
3.4.5. A starter
3.4.6. The traction relay of a starter
3.4.7. Gauges
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. A cover of a head of the block of cylinders
+ 3.4.13. Platens and коромысла
3.4.14. The thermostat of system of cooling
3.4.15. An inlet collector
3.4.16. A final collector
3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Турбокомпрессор
3.4.19. Турбонагнетатель
3.4.20. A radiator
3.4.21. Маслоохладитель
3.4.22. The fan
3.4.23. The pump of a cooling liquid
+ 3.4.24. A head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. A gear belt and covers
3.4.30. A chain and a cover (the engine 2,6)
3.4.31. The oil pallet
3.4.32. The oil pump and sajlent-platens (виброгасители)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. A back epiploon
3.4.37. Radical bearings
3.4.38. A flywheel
+ 3.4.39. An exhaust system
+ 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes
|
Starter arrangement on the engine
Starter with a direct drive
1. The screw
2. The traction relay
3. A sealant
4. An emphasis
5. The screw
6. A coupling bolt
7. A back cover
8. The back bearing
9. Щеткодержатель |
10. Ярмо with windings
11. An anchor
12. The lever
13. A washer
14. A lock ring
15. The restrictive plug
16. Обгонная муфта
17. A forward cover
|
Starter with a reducer
1, 3, 4. The screw
2. The traction relay
5. A back cover
6. Щеткодержатель
7. A brush
8. The back bearing
9. An anchor
10. Ярмо
11. A ball
12, 13. Уплотнители And and in
|
14. An emphasis
15. A planetary gear wheel
16. The lever
17. A lock ring
18. The restrictive plug
19. Обгонная муфта
20. A leading gear wheel
21. The holder
22. A forward cover
|
Specifications of starters
| Type | With a direct drive (1983-86), with a reducer (since 1987) |
| Rated power (Вт) | 900 (1983-86), 1200 Вт (since 1987) |
| Pressure, current and number of turns at bench tests | 11,5 In, 60 (1983-86), 100 And (1987), 90 And (since 1987), 6500 rpm (1983-86), 3000 rpm (since 1987) |
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Lift car redock. |
| 3. Disconnect wires, turn away 2 bolts of fastening and remove a starter. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is carried out upside-down. |
| 2. Tighten bolts with the demanded moment. |
|
|
|
