Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Engine major repairs
      3.4.1. An engine electric equipment
      3.4.2. The ignition distributor
      + 3.4.3. The generator
      3.4.4. The battery
      3.4.5. A starter
      3.4.6. The traction relay of a starter
      3.4.7. Gauges
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. A cover of a head of the block of cylinders
      + 3.4.13. Platens and коромысла
      3.4.14. The thermostat of system of cooling
      3.4.15. An inlet collector
      3.4.16. A final collector
      3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Турбокомпрессор
      3.4.19. Турбонагнетатель
      3.4.20. A radiator
      3.4.21. Маслоохладитель
      3.4.22. The fan
      3.4.23. The pump of a cooling liquid
      + 3.4.24. A head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. A gear belt and covers
      3.4.30. A chain and a cover (the engine 2,6)
      3.4.31. The oil pallet
      3.4.32. The oil pump and sajlent-platens (виброгасители)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. A back epiploon
      3.4.37. Radical bearings
      3.4.38. A flywheel
      + 3.4.39. An exhaust system
   + 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes


ccf2698e



3.4.38. A flywheel

THE GENERAL DATA

The prevention

The coupling casing is balanced together with a press disk. These details vary in steam.


Flywheel and leading disk

1. A flywheel
2. Transitive a flange And (on and / m with automatic transmission)
3. A leading disk
4. Transitive a flange In
5. An epiploon

Removal and installation

PERFORMANCE ORDER
1. Remove transmission and coupling.
2. On cars with the engine of 2,0 l on the hydrotransformer the gear wreath is provided, remove the hydrotransformer and check up a wreath condition. On all and / m (except and / m with the engine 2,0) turn away bolts of fastening of the transitive flange, a leading disk and the plug to коленвалу and remove a disk.
3. On cars from a mechanical check point designate flywheel position, turn away bolts in a diagonal order and remove a flywheel.
4. Replace a flywheel conducting a disk or the hydrotransformer at detection on them of damages or traces of deterioration.
5. Establish a flywheel conducting a disk, having combined the labels put at dismantling. The hydrotransformer is established on transmission (not on the engine). Tighten bolts with the moment 133 Н.м. On 4-cylinder engines or 74 Н.м. On 6-cylinder engines.

Gear wreath

At defects of a gear wreath the hydrotransformer replace.

At damage of a wreath of a flywheel it is recommended to replace a flywheel. Replacement of a gear wreath is supposed. For this purpose it is necessary to remove an old wreath and to heat up a new wreath to 300 With and напрессовать on a flywheel.