Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Engine major repairs
      3.4.1. An engine electric equipment
      3.4.2. The ignition distributor
      + 3.4.3. The generator
      3.4.4. The battery
      3.4.5. A starter
      3.4.6. The traction relay of a starter
      3.4.7. Gauges
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. A cover of a head of the block of cylinders
      + 3.4.13. Platens and коромысла
      3.4.14. The thermostat of system of cooling
      3.4.15. An inlet collector
      3.4.16. A final collector
      3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Турбокомпрессор
      3.4.19. Турбонагнетатель
      3.4.20. A radiator
      3.4.21. Маслоохладитель
      3.4.22. The fan
      3.4.23. The pump of a cooling liquid
      + 3.4.24. A head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. A gear belt and covers
      3.4.30. A chain and a cover (the engine 2,6)
      3.4.31. The oil pallet
      3.4.32. The oil pump and sajlent-platens (виброгасители)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. A back epiploon
      3.4.37. Radical bearings
      3.4.38. A flywheel
      + 3.4.39. An exhaust system
   + 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes

3.4.21. Маслоохладитель

THE GENERAL DATA

Маслоохладитель 4-cylinder engines

1. A bolt накидного the union
2. A lining
3. Tubes of the final party
4. Tubes of the pressure head party

5. Hoses
6. Маслоохладитель
7. An arm

Маслоохладитель 6-cylinder engines

1, 9. A bolt накидного the union
2, 10. Linings
3. Маслоохладитель
4. A rack
5. An arm

6. The union
7. A pressure head tube
8. An exhaust pipe
11, 12. Hoses

Arrangement of bolts of fastening of tubes and маслоохладителя 4-cylinder engines

Fastening bolts – are specified by arrows

Correct arrangement of pressure head and final tubes at assemblage

1, 5. Hoses

2. Clamping a collar

3. The terminator

4. A bolt накидного the union

Removal and installation

PERFORMANCE ORDER

1. Disconnect the battery from weight.

2. Merge oil.

3. Remove forward facing.

4. Turn away bolts of unions, keeping a key the welded nut on the cooler case. Get linings.

5. Turn away bolts and remove маслоохладитель.

6. Disconnect from маслоохладителя hoses and tubes.

7. Check up a condition of edges of a cooler and tubes. If necessary replace or repair.

8. At installation execute the following. On 4-cylinder engines: a long hose (the release party) establish above, and short – from below. On 6-cylinder engines: at first tighten a bolt of the union of a final hose, and then inlet then tighten a bolt of a clamping collar.

9. Further installation is carried out upside-down. Warm up the engine and check up oil level.