Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Engine major repairs
3.4.1. An engine electric equipment
3.4.2. The ignition distributor
+ 3.4.3. The generator
3.4.4. The battery
3.4.5. A starter
3.4.6. The traction relay of a starter
3.4.7. Gauges
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. A cover of a head of the block of cylinders
+ 3.4.13. Platens and коромысла
3.4.14. The thermostat of system of cooling
3.4.15. An inlet collector
3.4.16. A final collector
3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Турбокомпрессор
3.4.19. Турбонагнетатель
3.4.20. A radiator
3.4.21. Маслоохладитель
3.4.22. The fan
3.4.23. The pump of a cooling liquid
+ 3.4.24. A head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. A gear belt and covers
3.4.30. A chain and a cover (the engine 2,6)
3.4.31. The oil pallet
3.4.32. The oil pump and sajlent-platens (виброгасители)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. A back epiploon
3.4.37. Radical bearings
3.4.38. A flywheel
+ 3.4.39. An exhaust system
+ 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes
|
The distributor of ignition of engines of 2,0 and 2,6 l
|
1. A tip cover
2. A cover
3. A piece of coal
4. Бегунок
5. A wire
6. A wire on weight
7. The ignition block
8, 24 Pin
9. A rotor
10. A plate
11. A vacuum regulator with 2
Diaphragms
|
12. A vacuum regulator with 1 diaphragm
13. A rotor of a centrifugal regulator
14. A spring emphasis
15. A spring
16. Counterbalances
17. The platen
18. An epiploon
19. A sealant
20. A shaft
21. A ring
22. A washer
23. A gear wheel |
The distributor of ignition of the engine of 2,4 l
|
1. A cover
2. A sealant
3. A piece of coal
4. Бегунок
|
5. A wire
6. A ring
7. The case |
The ignition distributor 12-klapannogo the engine 3,0
|
1. A cover
2. A ring
3. A piece of coal
|
4. Бегунок
5. A ring
6. The case |
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Disconnect latches (or turn away screws) and remove a distributor cover together with wires, take aside. |
|
3. Designate distributor position on the block of cylinders. |
| 4. Designate and disconnect a hose from a vacuum regulator. |
| 5. Disconnect from the distributor a socket. |
|
6. Designate position бегунка concerning the distributor. |
|
7. Turn away a nut and get the distributor. Pay attention to a direction проворачивания бегунка at removal the distributor, designate position бегунка on the removed distributor. |
|
8. Remove a sealant from a distributor shaft. |
|
Installation
The prevention Коленвал at the removed distributor it was not turned.
| PERFORMANCE ORDER |
| 1. Installation is carried out upside-down. Replace a sealant. At installation will expose бегунок, in position designated after distributor removal, cautiously enter the distributor into the block of cylinders, slightly turn the platen, having entered drive gear wheels in gearing, and having pressed, put the distributor into place, having combined labels on the block of cylinders and the distributor case. |
The prevention Коленвал it was turned at the removed distributor
|
| 2. Expose the piston of 1st cylinder in ВМТ a compression step. For this purpose turn коленвал clockwise before label combination on a pulley or успокоителе with inflow on the block of cylinders. Remove клапанную a cover and check up springs of valves of 1st cylinder. If both springs or at least one turn коленвал on 1 turn are compressed. If коромысла rock, the piston of 1st cylinder is in ВМТ a compression step. |
|
3. Turn the distributor platen so that labels on a gear wheel and a distributor shaft (метки:1 – on a gear wheel, 2 – on a distributor shaft) have coincided. |
| 4. Enter the distributor into the block of cylinders, slightly turn the platen, having entered drive gear wheels in gearing, and put the distributor into place. If бегунок it was not combined with a conclusion for a candle of 1st cylinder submit the distributor back. Tighten the platen and again put наместо. |
| 5. Combine labels on the block of cylinders and the distributor case, tighten a bolt (nut) and establish all removed details. |
|
|
|
