Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Engine major repairs
3.4.1. An engine electric equipment
3.4.2. The ignition distributor
- 3.4.3. The generator
3.4.3.1. Specifications
3.4.3.2. Removal and installation
3.4.3.3. A pressure regulator
3.4.4. The battery
3.4.5. A starter
3.4.6. The traction relay of a starter
3.4.7. Gauges
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. A cover of a head of the block of cylinders
+ 3.4.13. Platens and коромысла
3.4.14. The thermostat of system of cooling
3.4.15. An inlet collector
3.4.16. A final collector
3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Турбокомпрессор
3.4.19. Турбонагнетатель
3.4.20. A radiator
3.4.21. Маслоохладитель
3.4.22. The fan
3.4.23. The pump of a cooling liquid
+ 3.4.24. A head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. A gear belt and covers
3.4.30. A chain and a cover (the engine 2,6)
3.4.31. The oil pallet
3.4.32. The oil pump and sajlent-platens (виброгасители)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. A back epiploon
3.4.37. Radical bearings
3.4.38. A flywheel
+ 3.4.39. An exhaust system
+ 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes
|
THE GENERATOR OF ENGINES OF 2,0 AND 2,6 L (WITHOUT THE CONDITIONER)
The generator of engines of 2,0 and 2,6 l (without the conditioner)
|
|
1. Sockets
2. The generator
3. Washers
4. An axial bolt
5. Lath |
Removal
| PERFORMANCE ORDER |
| 1. Switch off ignition and disconnect the battery from weight. |
| 2. Release bolts of the generator and remove a drive belt. On a part of cars it is required to remove the hydraulic booster pump. |
| 3. Disconnect generator conducting (preliminary having marked). Turn away a nut клеммных connections. |
| 4. Turn out an adjusting bolt and a nut of an axial bolt, take measures against loss of washers between the generator and an engine cover (are established on a part of cars). |
| 5. Get an axial bolt and remove the generator. |
|
Installation
| PERFORMANCE ORDER |
| 1. Establish the generator in a place. If the new unit pick up new washers on a thickness is established. For this purpose щупом check up a backlash between a forward cover, having submitted the generator forward. If the backlash is more 0,2 mm pick up washers so that they sliped under small effort between a cover and a back surface of the bottom arm. |
| 2. Insert an axial bolt and screw a nut. |
| 3. Turn an adjusting bolt and pull a belt. Tighten an adjusting bolt with the moment 12–13 Н.м. And an axial bolt – with the moment 20–24 Н.м. |
| 4. Establish all removed details. |
|
THE GENERATOR OF ENGINES OF 2,0 AND 2,6 L (WITH THE CONDITIONER)
The generator of engines of 2,0 and 2,6 l (with the conditioner)
|
|
1. A high pressure tube
2. A tube of low pressure
3, 5. A socket
4. The compressor
6. The generator |
Removal
| PERFORMANCE ORDER |
| 1. Depressurize a conditioner highway, having addressed in car-care centre. |
| 2. Disconnect from the compressor of a tube and a socket. Immediately muffle apertures. Turn away axial and adjusting bolts, remove a belt of a drive and the compressor, take him aside. |
| 3. Release bolts of the generator and remove a drive belt. Designate and disconnect sockets. |
| 4. Turn out top, and then the bottom bolt, having taken measures against loss of adjusting washers. Remove the generator. |
|
Installation
| PERFORMANCE ORDER |
| 1. Establish the generator in a place, insert the bottom bolt and pick up washers of the bottom bolt on a thickness so that the generator could be kept and was displaced aside under small effort. Tighten both bolts and pull a belt. Tighten the bottom bolt with the moment 13 Н.м. And the top bolt – with the moment 28 Н.м. Attach wires. |
| 2. Establish the compressor upside-down. At first slightly tighten a belt, having submitted the compressor by hand, not tightening bolts, then tighten bolts. Pull a belt, rotating an adjusting bolt. Immediately fill a highway with a coolant in car-care centre. |
| 3. If belts varied, through 80–160 km again check up their tension and adjust. |
|
DIESEL ENGINE
The diesel engine generator
|
|
1, 6. Маслопровод
2. A vacuum hose
3. A lath bolt
4. A belt
5. An axial bolt
7. The plug In
8. A socket |
Removal of a cover of the generator
|
|
1. A rotor
2. A shovel
3. A ring
4. The case |
Correct installation of blades of the pump
Correct installation of the case of the pump
|
|
Submit the pump in an arrow direction |
Conditions of a tightening of a bolt
|
|
1. A forward cover
2. A bolt
3. For backlash measurement to submit the generator on an arrow
The backlash And should be compensated before a bolt tightening. |
Removal
| PERFORMANCE ORDER |
| 1. Switch off ignition and disconnect the battery from weight. |
| 2. Disconnect a wire from the plug In on the generator. |
| 3. Disconnect from the vacuum pump hoses. |
| 4. Turn away a lock bolt, a nut of the bottom bolt and remove a belt. |
| 5. Turn away a through bolt and remove the generator in gathering with the pump. |
| 6. Turn away bolts and cautiously remove the pump. |
| 7. Check up a condition of shovels of the pump, a ring and an epiploon. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is carried out upside-down. |
| 2. Installation of blades with the slightest defects is not supposed. |
| 3. Establish the pump case according to a photo (fig. Correct installation of the case of the pump see). |
| 4. At first attach a hose to the pump then establish the generator. |
| 5. Compensate a backlash And (if it more than 0,2 mm), having established a washer. |
| 6. Pull a belt. |
|
ENGINES OF 2,4 L AND 12-KLAPANNYJ 3,0 L
The generator of engines of 2,4 l
|
1. An adjusting bolt
2. A lock bolt
3. A belt
|
4. An axial bolt
5. The generator |
The generator 12-klapannogo the engine of 3,0 l
|
1. An adjusting bolt
2. A cover
3. A lock bolt
|
4. A belt
5. An axial bolt
6. The generator |
Removal
| PERFORMANCE ORDER |
| 1. Switch off ignition and disconnect the battery from weight. |
| 2. Release bolts and remove a belt. If it is necessary to replace a belt remove the hydraulic booster pump. |
| 3. Disconnect generator conducting (preliminary having marked). Turn away a nut клеммных connections. |
| 4. Turn away a nut bottom bolts and an adjusting bolt. Remove the generator. |
|
Installation
Installation is carried out upside-down. Pull a belt and tighten bolts with the moment specified in illustrations.
ENGINES OF 3,0 L 24-KLAPANNYJ AND 3,5 L
The generator of engines of 3,0 l (24-klapannogo) и3,5 l
|
1. An axial bolt
2. A lock bolt
|
3. A belt
4. The generator |
Removal
| PERFORMANCE ORDER |
| 1. Switch off ignition and disconnect the battery from weight. |
| 2. Lift car redock. |
| 3. Release bolts and remove a belt. If it is necessary to replace a belt remove the hydraulic booster pump. |
| 4. Disconnect generator conducting (preliminary having marked). Turn away a nut клеммных connections. |
| 5. Turn away a lock bolt and a nut of the bottom bolt. Remove the generator. |
|
Installation
Installation is carried out upside-down. Pull a belt and tighten bolts with the moment specified in illustrations. |
|
Интернет Верхнее Велино, деревня смотрите на http://www.skscom.ru.