Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Engine major repairs
      3.4.1. An engine electric equipment
      3.4.2. The ignition distributor
      + 3.4.3. The generator
      3.4.4. The battery
      3.4.5. A starter
      3.4.6. The traction relay of a starter
      3.4.7. Gauges
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. A cover of a head of the block of cylinders
      + 3.4.13. Platens and коромысла
      3.4.14. The thermostat of system of cooling
      3.4.15. An inlet collector
      3.4.16. A final collector
      3.4.17. An incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Турбокомпрессор
      3.4.19. Турбонагнетатель
      3.4.20. A radiator
      3.4.21. Маслоохладитель
      3.4.22. The fan
      3.4.23. The pump of a cooling liquid
      + 3.4.24. A head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. A gear belt and covers
      3.4.30. A chain and a cover (the engine 2,6)
      3.4.31. The oil pallet
      3.4.32. The oil pump and sajlent-platens (виброгасители)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      - 3.4.35. Pistons and rods
         3.4.35.1. Replacement of a piston finger
         3.4.35.2. Replacement шатунных bearings
         3.4.35.3. Заглушки channels of the block of cylinders
      3.4.36. A back epiploon
      3.4.37. Radical bearings
      3.4.38. A flywheel
      + 3.4.39. An exhaust system
   + 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

3.4.35.1. Replacement of a piston finger

THE GENERAL DATA

Insert of the adaptation for rod deduction


Adjustment of position of a rod at выпрессовывании a finger

1. A rod

Directing adaptations for запрессовывания a finger

Выпрессовывание and запрессовывание a finger it is carried out in car-care centre on adaptation MD 998184-01 with a hydraulic press and the complete set special оправок. Effort at выпрессовывании about 1,78 Hardware, at запрессовывании – from 4,9 to 16,0 Hardware.

If a finger not запрессовывается with such effort a rod and (or) a finger replace.

Size check выступания a finger on each side the piston

At запресовывании a finger check up its size выступания (1) from both parties of the piston.

Выпрессованный the finger should pass in the piston under small effort. Otherwise the piston and (or) a finger replace.