Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
- 12. A body
   12.1. Maintenance service and repair
   12.2. Vinyl furnish
   12.3. An upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repairing of apertures from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. A windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. A cover of a back compartment
   12.16. Bumpers
   12.17. A forward facing lattice
   12.18. External mirrors
   12.19. The forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. The hatch
   12.23. The holder of a spare wheel
   + 12.24. The salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. A ceiling upholstery
   12.28. The door-lock switch
   + 12.29. Door glass, стеклоподъемник and the electric motor стеклоподъемника
   12.30. A windscreen
   12.31. Back glass
   12.32. Внутрисалонное a rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. An electric equipment
+ 14. Electroschemes

12.28. The door-lock switch

THE GENERAL DATA

Door-lock and the handle forward (above) and a back door (on inserts – greasing places at assemblage)


1. The button of blocking of the lock 2. The handle 3. Скоба	4. The lock switch 5. The lock mechanism 6, 7. The electric drive

Door-lock and the handle of a back cover (1992-98) (on an insert – a greasing place at assemblage)


1. Facing of a lantern of illumination Licence plate 2. The handle 3. The lock mechanism	4. The electric drive 5. Скоба 6. The lock switch

Door-lock and the handle of a back cover (1992-98) (on an insert – a greasing place at assemblage)


1. The internal panel and a water filter 2. An arm 3. Facing	4. The handle external 5. The handle internal 6. The lock 7. The electric drive

Removal and installation

The prevention

At dismantle of door-locks the part of fastenings of draughts of the mechanism of a drive of the lock will be damaged, therefore for assemblage prepare new fastenings (скобы, latches, etc.)

PERFORMANCE ORDER

1. Lower glass and remove the internal panel of a door.

2. Cautiously remove a windowpane sealant.

3. Remove скобы fastenings of draughts of the lock to the handle and a switch drum (on a part of cars it is recommended to disconnect draughts on the lock mechanism).

The switch of the lock which has been built in in the handle

4. Disconnect sockets of wires.

5. Turn away a nut and remove the handle. The lock should be removed from the handle in a workshop the qualified expert.

6. Installation is carried out upside-down.

The switch of the lock which has been built in at a door

7. Remove подковообразную скобу and remove a switch drum. Switch repair is under repair in a workshop the qualified expert.

8. Installation is carried out upside-down.

The switch of the lock of a back cover

9. Procedure differs nothing from described for door-locks.