Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
- 12. A body
   12.1. Maintenance service and repair
   12.2. Vinyl furnish
   12.3. An upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repairing of apertures from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. A windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. A cover of a back compartment
   12.16. Bumpers
   12.17. A forward facing lattice
   12.18. External mirrors
   12.19. The forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. The hatch
   12.23. The holder of a spare wheel
   + 12.24. The salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. A ceiling upholstery
   12.28. The door-lock switch
   + 12.29. Door glass, стеклоподъемник and the electric motor стеклоподъемника
   12.30. A windscreen
   12.31. Back glass
   12.32. Внутрисалонное a rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

12.25. Internal panels of doors
THE GENERAL DATA

The internal panel of a door
1. A figured spring ring
2. The handle стеклоподъемника
3. An overlay
4. The internal handle 		5. The switch стеклоподъемника
8. The panel
9. The door handle
10. A pocket

Removal and installation

PERFORMANCE ORDER
1. Remove triangular facing of a lateral mirror.
2. Remove заглушки, turn away screws and remove an armrest and the handle.
3. Turn away the screw, having removed заглушку, and remove an internal overlay of the door handle.
4. Wring out a figured spring ring and remove the handle стеклоподъемника. It is recommended to designate position of the handle by a sticky tape.
5. On a part of cars turn out the handle of a clamp of a door-lock (the square button of a clamp acts in film after a raising of the panel of a door).
6. Turn away fastening screws on a panel contour, thin flat вильчатым the tool remove latches (from 6 to 12 pieces (1 – a core, 2 – facing)).
7. Raise the panel, having deduced from gearing with the bottom uvulas, disconnect wires (if are available) and remove the panel. Do not damage a water filter in a door skeleton, otherwise water will get to salon.
8. At installation attach wires and combine the panel with the top edge of a door and besiege on uvulas easy blows of a palm.
9. Further assemblage is carried out upside-down.
10. Establish latches (1 – a sealant, 2 – a core, 3 – facing).
11. The handle стеклоподъемника establish on the pasted tape, having combined шлицы the handle and the platen.
12. Sharp blow of a palm on the platen centre drive the handle against the stop.