Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
- 12. A body
   12.1. Maintenance service and repair
   12.2. Vinyl furnish
   12.3. An upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repairing of apertures from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. A windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. A cover of a back compartment
   12.16. Bumpers
   12.17. A forward facing lattice
   12.18. External mirrors
   12.19. The forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. The hatch
   12.23. The holder of a spare wheel
   + 12.24. The salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. A ceiling upholstery
   12.28. The door-lock switch
   + 12.29. Door glass, стеклоподъемник and the electric motor стеклоподъемника
   12.30. A windscreen
   12.31. Back glass
   12.32. Внутрисалонное a rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

12.21. Body support (fastening to the chassis)
THE GENERAL DATA

Design and details of support of a 4-door body (1992-95)
1, 2. A bolt
3, 8, 9. A washer
4. A pillow of a support from a body
5. A pillow And
6. The plug 		7. A pillow In
10. The terminator
11. Самоподжимная a nut
12. A lining (to 1993)

Design and details of support of a 2-door body (1983-91)
N – at assemblage is subject to replacement
1, 9. A bolt
2, 6. A washer
3. A pillow And 		4. The plug
5. A pillow In
7. Самоподжимная a nut
8. A lining

Design and details of support of a 4-door body (1983-91)
N – at assemblage is subject to replacement
1, 8. A bolt
2, 6. A washer
3. A pillow And 		4. The plug
5. A pillow In
7. Самоподжимная a nut
9. A lining

If performance of any works it is necessary to remove bolts of fastening of a body the body should be raised only on height at which access is provided, it is forbidden to lift a body on considerable height as breakages are possible.

If it is necessary to replace any fastening of a body it is necessary to turn away all bolts of fastening of a body on the given party and to establish under a body of a support about each of fastenings.

PERFORMANCE ORDER
1. Lift the car, establish supports under each support, having laid wooden бруски. At least one support establish under a frame.
2. Turn away bolts of support of a body from that party on which work is carried out. At possibility remove a washer and the bottom pillow.
3. Clean a support from under frames and it is cautious приопустите a frame from that party on which work is carried out, do not suppose excessive lowering of a frame.
4. Again establish under a frame a support.
5. Remove the top pillow, the plug and linings.
6. Establish details of a support of a body upside-down.
7. Tighten nuts of support according to the demanded moments.