Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
- 12. A body
   12.1. Maintenance service and repair
   12.2. Vinyl furnish
   12.3. An upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repairing of apertures from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. A windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. A cover of a back compartment
   12.16. Bumpers
   12.17. A forward facing lattice
   12.18. External mirrors
   12.19. The forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. The hatch
   12.23. The holder of a spare wheel
   + 12.24. The salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. A ceiling upholstery
   12.28. The door-lock switch
   + 12.29. Door glass, стеклоподъемник and the electric motor стеклоподъемника
   12.30. A windscreen
   12.31. Back glass
   12.32. Внутрисалонное a rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. An electric equipment
+ 14. Electroschemes

12.20. Removal and installation covered

THE GENERAL DATA

Forward wing (1983-91гг.) (on inserts – places of greasing by EU-870 glue (above), drawings of hermetic 8531 on the top edge of a wing (section А–А), gluings of an edge of the protective panel to a wing (section in plane В–В))


1. A lattice 2. A forward combination of lamps 3. Headlight facing 4. The bottom panel передка 5. Грязеотражатель	6. A condensed edge of the protective panel 7. The protective panel of a niche 8. A wing 9. A sealing pillow of a corner of a wing

Forward wing (1992-98) (on inserts – places of drawing of hermetic)


1. Грязеотражатель 2. The forward index of turn	3. The protective panel

CARS 1983-91

PERFORMANCE ORDER

1. Turn away 6 screws and remove a forward lattice.
2. Remove a forward combination of lamps (subsection 13.17.4 see) and facing of headlights.
3. Turn away 4 screws and remove the bottom cross-section panel передка.
4. Remove грязеотражатели and the protective panel of a wheel niche.
5. Turn away bolts and remove a wing, having tracked for safety of a sealing pillow for protection of a forward corner of a wing.
6. Installation is carried out upside-down.
7. A sealing pillow establish on glue 3M Adhesive EU-870. An edge of the protective panel paste structure 3M ATD 8625.

CARS 1992-98

PERFORMANCE ORDER

1. Remove a bell of facing of an aperture of a wheel niche (if it is provided) for what execute the following.
	2. Paste masking tape on all length of lateral facing.
	3. Cut off facing on a glutinous layer by means of a scaffold in the thickness of 0,8 mm.
	4. Drill rivets of facing a drill in diameter of 4-5,5 mm. Cores of rivets beat out (1 – an insert of a mortgage rivet, 2 – заклека, 3 – a drill, 4 – the facing panel).
5. Remove latches, having submitted facing on itself.
The prevention If facing is established again, by means of a scaffold cut off a glutinous layer on a body not to break edge of the panel of facing. If glue does not give in to cutting heat up it to 40 ° With.
6. Шпателем remove a sticky tape.
7. Remove masking tape.
8. Wipe a surface degreasing structure 3M ATD 8906.
9. Remove a forward combination of lamps (subsection 13.17.4 see).
10. Turn away screws and remove the protective panel of a wheel niche.
11. Turn away bolts and remove a wing.
12. Installation is carried out upside-down.
13. Establish facing of an aperture of a wheel niche in a following order.
	14. Remove a scraper from lateral facing of a wing gluing tape.
15. Wipe a surface of facing of a wing degreasing structure 3M ATD 8906.
16. Put to a facing bell new 2-storonjuju gluing tape 3M ATD 6382.
	17. Heat up a surface of a tape till 40-60 ° With and remove a protective paper layer.
18. Establish facing on a wing so that latches have come into apertures, densely press facing.
	19. Rivet facing in places of remote rivets (1 – the adaptation, 2 – the panel of a body and facing, 3 – a mortgage rivet).