Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
- 12. A body
   12.1. Maintenance service and repair
   12.2. Vinyl furnish
   12.3. An upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repairing of apertures from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. A windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. A cover of a back compartment
   12.16. Bumpers
   12.17. A forward facing lattice
   12.18. External mirrors
   12.19. The forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. The hatch
   12.23. The holder of a spare wheel
   + 12.24. The salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. A ceiling upholstery
   12.28. The door-lock switch
   + 12.29. Door glass, стеклоподъемник and the electric motor стеклоподъемника
   12.30. A windscreen
   12.31. Back glass
   12.32. Внутрисалонное a rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e лечение спины

12.5. Repair of dents
THE GENERAL DATA

During carrying out of repair of dents the first, that it is necessary to make, it to correct a dent that the damaged place was as is possible more close to the initial form. There is no sense to try to restore completely the initial form as metal in the damaged place is stretched, and it cannot be restored to an initial contour. It is better to level a dent so that its level was approximately on 3 mm below level of surrounding metal.

In a case if the dent very small, in general is not present sense it to level.

The prevention

Strongly keep wooden брусок from a metal underside to absorb blows of a hammer and to prevent a metal stretching.

If the dent is in such part of a body which has a double layer, or something else does impossible access from within, it is necessary to apply other procedure.

PERFORMANCE ORDER
1. Drill some small apertures in metal in the damaged surface, mainly in the deepest parts.
2. Screw in long, self-cut screws in apertures so that they have entered into strong gearing with metal.
3. Now it is possible to correct a dent, having pulled for acting heads of screws by means of flat-nose pliers.
4. The following stage of repair is a removal of a paint from the damaged surface and from surrounding metal approximately on 2,5 see
5. It becomes by means of a wire brush or a disk for the polishing, put on a drill, however with not smaller efficiency it can be made manually by means of an emery paper.
6. To finish preparations to шпатлевке, smooth out a screw-driver or a file a surface of the bared metal, or drill small apertures in the damaged area.
7. It will provide good coupling of metal and лессировки.
8. To finish repair, look subsection 12.7.