Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
- 11. Brake system
   11.1. Technical characteristics
   11.2. The vacuum amplifier of brakes
   11.3. Adjustment of brakes
   11.4. The switch of a signal of braking
   11.5. Removal and pedal installation
   11.6. The main cylinder of brakes
   11.7. The dosing out valve
   11.8. A regulator of pressure of back brakes (1992-98)
   11.9. The control valve of the amplifier of brakes
   11.10. Hoses and tubes
   11.11. Removal of air from a hydrodrive of brakes
   - 11.12. Forward disk brakes
      11.12.1. Колодки disk brakes
      11.12.2. A brake support
      11.12.3. A brake disk
   + 11.13. Back drum-type brakes
   + 11.14. Back disk brakes (1992-98)
   + 11.15. A manual brake
   11.16. Antiblocking system (ABS)
   11.17. The hydromodule
   11.18. The overload gauge
   11.19. The gauge of speed
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes


ccf2698e



11.12.2. A brake support

THE GENERAL DATA

Support of a forward brake (on inserts greasing places before assemblage are specified)

 
1. A finger
2. An axis
3. A support in gathering
4, 5. The plug
6, 7, 9. A cover
8. A ring
10. The piston
11. A sealant
12. The case
13, 14. Plates
15. Колодки
16. Скоба
17. A support arm

For greasing the structure from ремкомплекта is used.

Described procedure is applicable also to a 2-cylinder support of cars 1992-98

Removal and installation

PERFORMANCE ORDER
1. Lift redock of the car and remove a wheel.
2. Remove a part of a liquid from a tank.
3. Disconnect and muffle a hose.
4. Turn away bolts fastenings (fingers) of a support.
5. Get fingers of a support and store them in the pure container.
6. Remove a support.
7. Remove external колодку.
8. Remove a plate колодки.
9. Remove internal колодку.
10. Remove top and bottom скобы.
11. Installation is carried out upside-down taking into account the following.
12. Drown the piston in the cylinder.
13. Tighten connections with following moments: support bolts – 32–42 Н.м. (Bottom) and 40–50 Н.м. (Top), the hose union – 17 Н.м.
14. Remove air from a hydrodrive.

Dismantling

PERFORMANCE ORDER
1. Remove a lock ring of a cover of the piston.
2. Remove a cover.
3. Cautiously remove pistons the compressed air.
4. Cautiously get from the cylinder a cuff.
5. Check up a condition of pistons.
6. Check up a condition of an internal surface of the cylinder.
7. At detection of corrosion and appreciable damages of a detail replace. In ремкомплект a support enter уплотнители and the piston (it is delivered also separately), and also greasing for support fingers.
8. Assemblage is carried out upside-down.
9. Replace all уплотнители.
10. Remove a piston cover.
11. Take a piston sealant.
12. Grease fingers of a support with structure from ремкомплекта. The piston grease with a brake liquid.