Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
- 11. Brake system
   11.1. Technical characteristics
   11.2. The vacuum amplifier of brakes
   11.3. Adjustment of brakes
   11.4. The switch of a signal of braking
   11.5. Removal and pedal installation
   11.6. The main cylinder of brakes
   11.7. The dosing out valve
   11.8. A regulator of pressure of back brakes (1992-98)
   11.9. The control valve of the amplifier of brakes
   11.10. Hoses and tubes
   11.11. Removal of air from a hydrodrive of brakes
   + 11.12. Forward disk brakes
   + 11.13. Back drum-type brakes
   + 11.14. Back disk brakes (1992-98)
   + 11.15. A manual brake
   11.16. Antiblocking system (ABS)
   11.17. The hydromodule
   11.18. The overload gauge
   11.19. The gauge of speed
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

11.6. The main cylinder of brakes
THE GENERAL DATA

Details of the main cylinder of brakes (1983-86)
1. A tank stopper
2. A washer
3. A diaphragm
4. A float
5. A tank
6. The holder
7. The gauge
8. The union
9. A hose
10. Заглушка
 11. A saddle
12. The valve
13. A spring
14. The valve case
15. The cylinder
16. A restrictive bolt
17, 18. Pistons with springs
19. A lock ring
20. A spring

Details of the main cylinder of brakes (1987-98)
N – at dismantling is subject to replacement
1. A socket of the gauge of level of a liquid
2. The union of tubes
3. A socket
4. The main cylinder
5. An arm

Adjustment выступания an amplifier rod
6. A tank stopper
 7. A bolt
8. A tank
9. A diaphragm
10. A float
11. Consolidation
12. A restrictive bolt
13. A lining
14. A lock ring
15, 16. Pistons with springs

Removal and installation

PERFORMANCE ORDER
1. Remove from a tank a liquid.
2. Disconnect a wire from the indicator of level of a liquid.
3. Disconnect from the cylinder of the union of tubes of a hydrodrive of brakes.
4. Turn away a nut and remove the cylinder.
5. Installation is carried out upside-down.
6. Tighten all connections according to the demanded moments.
7. Remove air from a hydrodrive.

Dismantling and assemblage

PERFORMANCE ORDER
1. Remove a liquid from a tank.
2. Disconnect a socket of the gauge of level of a liquid.
3. Disconnect a lateral tube of brakes.
4. Disconnect a forward tube of brakes.
5. Turn away a nut.
6. Remove the cylinder.
7. Clamp the cylinder in a vice for a flange.
8. Turn away a bolt and remove a tank.
9. Turn on накидные nuts and get linings.
10. Turn out a restrictive bolt of the piston.
11. Remove a lock ring.
12. Get the first piston (the piston not to unbend).
13. Get the second piston.
14. At dismantling pay attention 10 times of an arrangement of details.
15. Assemblage is carried out upside-down taking into account the following.
16. Check up diameter of the cylinder in 6 places in mutually perpendicular directions. If the disorder of measurements exceeds 0,025 mm the cylinder in gathering replace.
17. Check up a backlash between the piston and the cylinder which should be no more than 0,15 mm, otherwise the cylinder in gathering replace.
18. Replace all уплотнители.
19. Tighten all connections on the cylinder according to the demanded moments.
20. Before cylinder installation define a backlash And under the formula And = In – With – D.
21. For definition And measure distance In through a plate with precisely measured thickness.
22. Measure distance With.
23. Then measure distance D through a plate with precisely measured thickness.
24. Calculate A.Zazor's distance it should be equal 0,1–0,15 mm.
25. If necessary adjust a backlash And, rotating a rod of the amplifier of brakes and measuring distance D.
26. After the termination pump over brakes.