Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   + 3.4. Engine major repairs
   - 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
      3.5.1. Removal and engine installation
      3.5.2. Engine dismantling
      3.5.3. Pistons and rods
      3.5.4. Valves and shaft коромысел
      3.5.5. A head of cylinders and valves, shaft коромысел and коромысла
      3.5.6. A head of cylinders
      3.5.7. Compression check
      3.5.8. A camshaft and газораспределительный the mechanism
      3.5.9. A mechanism drive газораспределения
      3.5.10. Adjustment of backlashes of valves
      3.5.11. Adjustment of a tension of a gear belt
      3.5.12. Removal of the bottom protective casing of a gear belt
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes


ccf2698e



3.5.5. A head of cylinders and valves, shaft коромысел and коромысла

THE GENERAL DATA

Correct assemblage of a shaft коромысел

1. Коромысла inlet valves

2. Коромысла final valves

Each of springs (3) settles down between коромыслами.

The assembly drawing of a head of cylinders of the diesel engine

1. A ventilation hose
2. A stopper маслозаливной горловигы
3. A cover of a head of cylinders
4. A lining of a cover of a head of cylinders
5. Semicircular consolidation
6. A shaft коромысел
7. Коромысло the inlet valve
8. Коромысло the final valve
9. A shaft spring коромысел
10. The adjusting screw
11. A camshaft epiploon
12. A cover of the forward bearing
13. Bearing N2 cover
14. Bearing N3 cover
15. Bearing N4 cover
16. A cover of the back bearing
17. A camshaft

Коромысла inlet and final valves differ and have marks or "I" (inlet valves), or "Е" (final valves). Apertures for oil injection on a shaft коромысел should settle down after installation from below. The end of a shaft with one lubricant aperture should settle down from the forward party. On other end of a shaft there are two lubricant apertures.

Covers of bearings N2, 3 and 4 have marks with their numbers. Covers of bearings N1 and 5 are not marked, as they can be distinguished under their form.

The shaft коромысел is established after camshaft installation.
PERFORMANCE ORDER
1. Grease all details of the mechanism коромысел with engine oil and establish коромысла and springs on a shaft.
2. Insert both bolts and spring washers and tighten bolts the moment of an inhaling from 35 to 40 Н m.
3. Other works are carried out to similarly petrol engines. Establish a gear belt and other details of a drive газораспределительного the mechanism. On fig. the Assembly drawing of a head of cylinders of the diesel engine shaft details коромысел are presented. After installation adjust backlashes of valves on the cold engine and finish them to preset values after an engine warming up.