Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   + 3.4. Engine major repairs
   - 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
      3.5.1. Removal and engine installation
      3.5.2. Engine dismantling
      3.5.3. Pistons and rods
      3.5.4. Valves and shaft коромысел
      3.5.5. A head of cylinders and valves, shaft коромысел and коромысла
      3.5.6. A head of cylinders
      3.5.7. Compression check
      3.5.8. A camshaft and газораспределительный the mechanism
      3.5.9. A mechanism drive газораспределения
      3.5.10. Adjustment of backlashes of valves
      3.5.11. Adjustment of a tension of a gear belt
      3.5.12. Removal of the bottom protective casing of a gear belt
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes


ccf2698e



3.5.10. Adjustment of backlashes of valves

THE GENERAL DATA

Label position on a gear pulley of a camshaft

The label is specified by an arrow.

Adjustment of backlashes of valves on the diesel engine


1. Накидной a key

2. A screw-driver

3. Щуп

For providing of access to valves it is necessary to perform preliminary works. It concerns mainly removal of the top protective casing of a gear belt and a cover of a head of cylinders. Exposed value of backlashes of inlet and final valves makes 0,25 mm.
PERFORMANCE ORDER
1. Turn away the top protective casing of a gear belt. The casing fastens four bolts on the forward party. Pull out a casing forward and drag under a water hose.
2. Disconnect from a cover of a head of cylinders a ventilation hose картера the engine and a pressure head hose наддувного обогатителя from the fuel pump of a high pressure.
3. Release a cable of gas from a clip on a cover of a head of cylinders and will put it aside, not bending.
4. Turn away bolts of a cover of a head of cylinders and remove a cover. The semicircular sealing insert from the back party of a head of cylinders thus should not drop out.
5. Turn a cranked shaft before installation of the piston of the first cylinder in position of the top dead point. Thus should coincide a label on a gear pulley of a camshaft and a triangular label on the top part of the case газораспределительного the mechanism, as is shown in fig. label Position on a gear pulley of a camshaft.
6. At this position of the engine adjust backlashes of following valves: inlet and final valves of the first cylinder, the inlet valve of the second cylinder, the final valve of the third cylinder.
7. After that turn the engine on one turn and adjust backlashes of following valves: the final valve of the second cylinder, the inlet valve of the third cylinder, inlet and final valves of the fourth cylinder. At adjustment use накидным a key, a screw-driver or щупом a corresponding thickness. Put tools, as is shown in fig. Adjustment of backlashes of valves on the diesel engine. Valves on the diesel engine are located, since the party with a water hose, in a following order: the final valve, the inlet valve and further in the same order to the fourth cylinder.