Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
- 3. Engines
3.1. Candles
3.2. Check of wires
- 3.3. Ignition system
3.3.1. Adjustments
3.3.2. Check of the gauge of rotation коленвала
3.3.3. The coil of ignition and additional резистр
+ 3.3.4. Replacement of details of system of ignition
3.3.5. Ignition installation
3.3.6. Adjustment of backlashes in valves
3.3.7. Adjustment of turns of idling and quality of a mix
3.3.8. Adjustment of structure of a mix
+ 3.4. Engine major repairs
+ 3.5. Diesel and турбодизельный engines of 2,5 and 2,8 l
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes
|
Exhibiting статора and a gauge rotor at backlash measurement
|
|
1. Статор
2. A rotor
Check up a backlash between статором and a rotor not magnetic щупом which should be 0,2 mm. |
Valves are regulated only on a diesel engine, other engines are equipped by hydropushers. On a part of engines valves of jets of additional injection which demand adjustment by a special technique also are provided.
Backlashes of inlet and final valves on прогретом the engine of 0,25 mm.
DIESEL ENGINE OF 2,3 L
Adjustment
| PERFORMANCE ORDER |
| 1. Warm up the engine. |
| 2. Stop the engine and switch off ignition. |
| 3. Expose the piston of 1st cylinder in ВМТ a compression step. For this purpose turn коленвал clockwise before label combination on a pulley or успокоителе with inflow on the block of cylinders. Remove клапанную a cover and check up springs of valves of 1st cylinder. If both springs or at least one turn коленвал on 1 turn are compressed. If коромысла rock, the piston of 1st cylinder is in ВМТ a compression step. |
|
4. Release counternuts And. |
| 5. Establish a backlash of 0,25 mm and tighten a counternut. |
| 6. Expose the piston of 4th cylinder in ВМТ a step of compression and adjust backlashes in valves of Century |
| 7. Establish the removed details. |
| 8. Check up idling turns. |
|
ENGINES OF 2,0 AND 2,6 L
On these engines valves of fuel jets of the chamber of combustion are regulated only.
| PERFORMANCE ORDER |
| 1. Warm up the engine. |
| 2. Stop the engine and switch off ignition. |
| 3. Check up the moment of an inhaling of bolts of a head of cylinders (subsection 3.5.6 see). |
| 4. Expose the piston of 1st cylinder in ВМТ a compression step. For this purpose turn коленвал clockwise before label combination on a pulley or успокоителе with inflow on the block of cylinders. Remove клапанную a cover and check up springs of valves of 1st cylinder. If both springs or at least one turn коленвал on 1 turn are compressed. If коромысла rock, the piston of 1st cylinder is in ВМТ a compression step. |
| 5. Release a valve counternut жиклераи rotating the screw, establish a backlash of 0,25 mm (щуп should slip with small effort). Tighten a counternut. |
| 6. Adjust backlashes of valves of other cylinders, according to an engine operating procedure. |
| 7. Establish the removed details. |
| 8. Check up idling turns. |
|
ENGINES 2,4, 3,0 AND 3,5 L
Backlashes in valves of these engines are established only at repair of a head of cylinders (subsection 3.5.6 and subsection 3.4.24 see). |
|
