Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
- 9. A running part
   + 9.1. A mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. The mechanism of management of transmission
      9.3.5. A shaft epiploon картера transmissions
      9.3.6. Removal and transmission installation
      9.3.7. A distributing box
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward карданный a shaft and крестовины
      + 9.3.10. Back карданный a shaft and крестовины
      9.3.11. A forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semiaxes and epiploons of a forward axis
      9.3.15. A reducer of a forward axis
      9.3.16. Dismantling of SHRUS
   + 9.4. The back bridge
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes


9.3.14. Forward semiaxes and epiploons of a forward axis


Forward semiaxes

1. A guard
2, 3. A cap
4. A lining
5. A lock ring
6. A washer
7. A forward brake
8, 10, 12. Шплинт
9. A tip of steering draught
11, 13. A spherical support
14. A forward nave
15. Left полуось
16. A spring ring
17. Right полуось

The right semiaxes

1. A nave
2. External полуось
3. Internal полуось
4. A spring ring
5. Самоподжимная a nut
6. An arm
7. The case

Details of the right internal semiaxis

1. Полуось
2. The bearing
3. A cover
4. The case
5. An epiploon

Removal, installation and dismantling

1. Before the beginning of works unblock naves of forward wheels.
2. Remove forward wheels, remove a forward brake, take aside and fix.
3. Remove the mechanism of blocking of a nave, get a lock ring of a semiaxis.
4. Выпрессуйте a stripper a finger of steering draught, расшплинтовав and having turned away a nut.
5. Выпрессуйте a stripper at first bottom, then the top spherical support, remove a nave in gathering with a rotary fist and a pin.
6. Cautiously get left полуось.
7. Designate position of the right external semiaxis and remove it.
8. Remove right internal полуось (using strippers MB990241-01 and MB990211-01).
9. Remove the case of the right semiaxis. For this purpose remove a spring ring of an internal semiaxis, turn on самоподжимную a nut of an arm of the case and remove an arm.
10. At bearing removal unbend edges of a dustproof cover.
11. Establish the adaptation for bearing fixing so that a facet And has rested against a bearing holder.
12. For выпрессовки the bearing establish полуось with the adaptation on бруски and hammer blows beat out полуось.
13. Press from an internal semiaxis a cover, remove from the case of a semiaxis an epiploon.


1. Запрессуйте a new epiploon in the case of a semiaxis by means of adaptation MV990955-01 so that the epiploon surface was заподлицо with a case end face.
2. Оправкой 75х4 mm запрессуйте on internal полуось a dustproof cover also fill a cavity of a cover with greasing.
3. Напрессуйте on полуось the bearing by means of a press and equipment (МD990560 and МВ998348-01).
4. Dress on a semiaxis new spring rings and insert into a reducer, пристукнув a rubber hammer, establish the case of the right semiaxis.
5. Attach right полуось to internal, having tightened nuts with the moment 54 Н.м.
6. Establish the shock-absorber (if acted in film).
7. Establish a rotary fist with a nave (fig. subsection 10.2.8 see).
8. Establish adjusting washers and a lock ring, check up axial люфт which should be 0,2–0,5 mm. If necessary adjust люфт selection of washers.
9. Establish a nave cap, tighten bolts with the moment 10–14 Н.м.
10. Establish a forward brake and tighten bolts with the moment 80–100 Н.м.
11. Establish wheels and lower the car.