Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
- 9. A running part
+ 9.1. A mechanical transmission
+ 9.2. Coupling
- 9.3. Automatic transmission
9.3.1. Adjustments
+ 9.3.2. The blocking switch
9.3.3. Check of adjustment of a cable of management by transmission
9.3.4. The mechanism of management of transmission
9.3.5. A shaft epiploon картера transmissions
9.3.6. Removal and transmission installation
9.3.7. A distributing box
9.3.8. Forward and back epiploons
+ 9.3.9. Forward карданный a shaft and крестовины
+ 9.3.10. Back карданный a shaft and крестовины
9.3.11. A forward leading axis
9.3.12. A nave with a manual unblocking
9.3.13. A nave with an automatic unblocking
9.3.14. Forward semiaxes and epiploons of a forward axis
9.3.15. A reducer of a forward axis
9.3.16. Dismantling of SHRUS
+ 9.4. The back bridge
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes
|
CARS 1983-86
Adjustment of inclusion of a kick-down-mode
The screw of adjustment of inclusion of a kick-down-mode (М904А)
|
|
The adjusting screw is on the left side картера transmissions.
1. To a cooler
2. The adjusting screw |
| PERFORMANCE ORDER |
| 1. Turn away a counternut on 5 turns. |
| 2. Be convinced, that the screw rotates without jammings. |
| 3. Tighten the screw with the moment 7,8 Н.м. |
| 4. Turn away the screw on 3,5 turns, and, keeping it, tighten a counternut with the moment 40–55 Н.м. |
|
Adjustment of a tape of inclusion of a backing and the lowest transfer (low-reverse)
The screw of adjustment of inclusion of a backing and the lowest transfer
|
|
1. The screw
2. A counternut |
| PERFORMANCE ORDER |
| 1. Lift the car. |
| 2. Turn away a counternut on 5 turns. |
| 3. Be convinced, that the screw rotates without jammings. |
| 4. Key MD998358 tighten the screw with the moment 4,9 Н.м. |
| 5. Turn away the screw on 7 turns, and, keeping it, tighten a counternut with the moment 34–47 Н.м. |
| 6. Establish the pallet and tighten bolts with the moment 15–20 Н.м. |
| 7. Fill in a liquid. |
|
Kick-down-drive adjustment
CARS 1983-86
Adjustment of system of draughts of a kick-down-mode (М904А)
|
|
1. Draught With
2. A bolt
3. Draught In
4. A control lever throttle заслонкой
5. Draught And |
Check of turn of draught of management throttle заслонкой (after adjustment of other draughts)
|
|
1. Position at completely open throttle заслонке
2. Position idling
3. The lever |
| PERFORMANCE ORDER |
| 1. Release bolts so that draughts In and With freely moved. |
| 2. Warm up the engine to 80 ° With and be convinced that fast idling is completely disconnected (a cam of the lever air заслонки the carburettor should not adjoin to a cam of the lever throttle заслонки). |
| 3. Submit draught And (or a control lever throttle заслонкой) to the terminator of idling and establish draughts in the position corresponding to idling. |
| 4. Tighten a bolt connecting draughts In and With. |
| 5. Be convinced, that at opening throttle заслонки the lever on transmission turns on 47,5–54 °, and also that at slow return of draught throttle заслонки from completely open position заслонки the lever on transmissions comes back in the position corresponding to idling under the influence of a spring. |
|
CARS 1987-89
Kick-down-drive adjustment (КМ148)
|
|
1. Completely opened заслонка
2. Idling
3. An arm |
| PERFORMANCE ORDER |
| 1. Believe idling turns (after idling adjustment adjust a cable throttle заслонки). |
| 2. Check up distance between the terminator of a cable and a cap which 52–53 mm should be at completely opened заслонке. |
| 3. If necessary establish distance moving of an arm of a cable at the released bolts. |
|
CARS 1990-98
Adjustment of a backlash of a cable of a kick-down-drive (а/м with engines of 3,5 l and 3,0 l 1990-94гг.)
|
|
1. Nuts
2. A cover
3. The cable terminator |
Adjustment of a backlash of a cable of a kick-down-drive (а/м with the engine of 1995 of 3,0 l)
|
|
1. Nuts
2. The cable terminator
3. A cover |
| PERFORMANCE ORDER |
| The engine of 3,5 l and 3,0 l (1990-94) |
| 1. Press a pedal throttle заслонки and check up distance between the terminator of a cable and a dustproof cover which should be 0–1 mm. |
| 2. If necessary establish distance rotation of adjusting nuts of a cover of a cable. |
| The engine of 3,0 l (1995) |
| 3. Remove a cover of a cable and and check up distance between the terminator of a cable and a cover which 34–35 mm should be at completely opened заслонке. |
| 4. If necessary establish distance rotation of adjusting nuts of a cover of a cable. |
|
|
|
