Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
- 9. A running part
   + 9.1. A mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. The mechanism of management of transmission
      9.3.5. A shaft epiploon картера transmissions
      9.3.6. Removal and transmission installation
      9.3.7. A distributing box
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward карданный a shaft and крестовины
      + 9.3.10. Back карданный a shaft and крестовины
      9.3.11. A forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semiaxes and epiploons of a forward axis
      9.3.15. A reducer of a forward axis
      9.3.16. Dismantling of SHRUS
   + 9.4. The back bridge
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes

9.3.16. Dismantling of SHRUS

THE GENERAL DATA

Details of the SHRUS of type Double-offset of the right semiaxis

1. A collar And
2. A collar In
3. A spring ring
4. An external holder
6. Balls
7. A separator
8. A lock ring
9. An internal holder

10. A cover
11. A dustproof cover
12. Летна the protective case of a cover
13. The protective case of a cover
14. A collar And
15. Хамут In
16. A cover of the SHRUS of type Bierfiild

Details of the SHRUS of type Double-offset of the left semiaxis

1. A collar And
2. A collar In
3. A spring ring
4. An external holder
5. A dustproof cover
6. Balls
7. A separator
8. A lock ring
9. An internal holder
10. A cover
11. A dustproof cover
12. A tape of the protective case of a cover

13. The protective case of a cover
14. A collar And
15. A collar In
16. A cover of an external SHRUS of type Bieriild
17. Полуось an external SHRUS of type Bieriild
18. A spring ring

Assemblage is carried out in
Sequences (under numbers of positions) 17–16–14–15–2–10–1–7–9–8–
–6–5–4–3–18–13–12–11

The device of the SHRUS of type Double-offset

1. A separator

2. A lock ring

3. An internal holder

On considered cars folding SHRUS, – axial type DOJ (double-offset) or TJ (tripod), – c an inside and not folding, – BJ (type Bierfiild) or RJ (type Rzeppa), – from lateral aspect are established.

Regularly check a condition of covers of SHRUS, at the slightest visible damages covers immediately replace.

At dismantling of SHRUS it is necessary to replace collars of covers and spring rings, keep in mind, that these details невзаимозаменяемы for models of different years of release and at their acquisition it is necessary to specify a code by the catalogue.

PERFORMANCE ORDER

SHRUS of type Тripod
1. Remove the big and small collars and remove a hinge cover, having displaced it on a semiaxis.
2. Cautiously remove a hinge holder.
3. Remove a lock ring and remove крестовину, wash out it, but do not assort.
	4. Remove крестовину, having wrapped up an insulating tape шлицы semiaxes, and remove a cover.
5. Check up a condition of details.
6. Collect and establish the hinge upside-down.
7. Grease крестовину with the greasing delivered in ремкомплекте.
SHRUS of type Double-offset
8. Dismantling-assemblage are carried out according to numbers of positions (fig. of the Detail of the SHRUS of type Double-offset of the left semiaxis see).
9. At dismantling designate labels an initial relative positioning of a separator and an internal holder of the SHRUS and a semiaxis which at assemblage combine.
10. Grease a holder and a separator of the hinge with the greasing delivered in ремкомплекте, establish balls.
	11. Fill an external holder with greasing approximately on 1/3, establish a lock ring and collect the SHRUS. With the greasing rest fill an underside of the hinge or a cover.

Replacement of covers of SHRUS

PERFORMANCE ORDER

1. The replacement procedure of a cover of an internal SHRUS practically differs nothing from a dismantling order (see above).

2. The cover of an external SHRUS acts in film after removal of an internal SHRUS and removal of collars.

3. At assemblage about 1/2 greasings put in pawn in the hinge and 1/2 – in a new cover.

4. Replace cover collars.