Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
- 6. The power supply system
   6.1. Introduction
   6.2. Removal of air from the power supply system
   6.3. Removal of water from the fuel filter
   6.4. Replacement of a filtering element of the fuel filter
   6.5. Removal and installation ТНВД
   6.6. Idling adjustment
   6.7. Check of system of prestarting heating of the engine 4D56Т
   6.8. Check of the block of management by prestarting heating
   6.9. Check of the relay of inclusion of starting candles
   6.10. Removal and installation турбокомпрессора
   6.11. Check of pressure of pressurisation
   6.12. The Vozduho-air cooler
+ 7. Release system
+ 8. Fuel system
+ 9. A running part
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

6.5. Removal and installation ТНВД
THE GENERAL DATA

The fuel pump of a high pressure

  
1. ТНВД
2. A gear pulley of a drive of the pump
3. The gauge of number of turns
4. A hose of the proof-reader of giving of fuel on pressure of pressurisation
5. High pressure pipelines
 6. Pipelines fuel plum
7. An atomizer
8. An atomizer lining
9. A lining of the case of an atomizer
10. A lining of the pipeline fuel plum
11. A nut of the pipeline fuel plum

Removal

PERFORMANCE ORDER
1. Disconnect wires from plugs of the storage battery.
2. On cars with the vozduho-air heat exchanger disconnect electric wires from the cooler electrofan, disconnect from a cooler air hoses, turn away four bolts of fastening of an arch and remove all knot.
3. Disconnect a compensatory hose of a turbo-supercharging.
4. Disconnect from the pump electric wires (fig. the Fuel pump of a high pressure see).
5. Disconnect from the pump pipelines of a supply and fuel tap, a cable of management of giving of fuel and high pressure pipelines.
6. Remove the top cover of a drive газораспределительного the mechanism.
7. Rotating a cranked shaft clockwise a key for a bolt of fastening of a pulley, combine labels on a pulley of a camshaft (1) and a pulley of drive ТНВД with adjusting pins (2) on the block and ослабьте a tension of a gear belt.
8. Turn away a nut of fastening of a gear pulley of drive ТНВД and remove a pulley (2) by means of a stripper (1). Turn away two forward bolts of fastening ТНВД.
9. Remove a back arm of fastening of the pump then remove ТНВД.

Installation

PERFORMANCE ORDER
1. Screw two forward bolts of fastening of the pump and establish into place a back arm of fastening of the pump.
2. Establish a gear pulley of drive ТНВД, screw and tighten a nut of a pulley the moment of 8,0-9,0 kgs/m.
3. Put on a pulley of drive ТНВД a gear belt, preliminary having combined adjusting labels.
4. Adjust an initial corner of an advancing of giving of fuel ТНВД as it is described more low. Tighten bolts of fastening of the pump.
5. Establish the top cover of a drive газораспределительного the mechanism.
6. Attach to the pump high pressure pipelines, a cable of management of fuel giving, pipelines of a supply and fuel tap.
7. Attach a hose to the proof-reader of giving of fuel on pressure of pressurisation of the pump.
8. Connect to the pump electric wires.
9. Establish into place the vozduho-air heat exchanger if it is available.
10. Connect wires to plugs of the storage battery.
11. Start the engine and check up its work idling.

Adjustment of an initial corner of an advancing of giving of fuel ТНВД

PERFORMANCE ORDER
1. Turning a cranked shaft clockwise a key for a bolt of fastening of a pulley, establish the piston of 1st cylinder in ВМТ the end of a step of compression.
2. Thus the label on a pulley of a cranked shaft should be opposite to label TDC ("ВМТ") on the bottom cover of a drive газораспределительного the mechanism.
3. Turn out a carving stopper which is in a back part of the pump between unions of pipelines of a high pressure.
4. In an aperture under a stopper screw rack MD 998384, having preliminary convinced, that its mobile probe acts on 10 mm (1 – the indicator, 2 – ТНВД).
5. Fix the indicator on the rack end.
6. Turn a cranked shaft counter-clockwise so that the piston of 1st cylinder was established approximately in 30 ° to ВМТ.
7. In this position establish an arrow of the indicator on zero. Slightly turning a cranked shaft in that and other party, be convinced, that the arrow of the indicator does not respond.
8. Otherwise repeat the previous operation.
9. Turning a cranked shaft clockwise, combine a label corresponding to a corner of an advancing of injection of fuel on 2 °, 5 ° and 7 ° after ВМТ (depending on engine model), on a pulley of a cranked shaft with an adjusting label on the bottom cover of a drive газораспределительного the mechanism.
10. In this position the indicator should show 1±0,03 mm.
11. If the indicator shows other size, ослабьте two forward bolts of fastening of the pump and bolts of fastening of a back arm of the pump.
12. Release the union of pipelines of a high pressure.
13. If indications of the indicator less the than demanded size, displace the pump to the engine and on the contrary.
14. Tighten forward bolts of fastening of the pump and bolts of fastening of a back arm of the pump.
15. Tighten the union of pipelines of a high pressure.
16. Remove the indicator and turn out from the pump an indicator rack.
17. Screw in a pump aperture a carving stopper, preliminary having replaced a lining.