Mitsubishi Pajero

1982-1998 of release

Repair and car operation


Митсубиси Паджеро
+ 1.1. The instrument panel and control means
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. The power supply system
+ 7. Release system
+ 8. Fuel system
- 9. A running part
   + 9.1. A mechanical transmission
   + 9.2. Coupling
   + 9.3. Automatic transmission
   - 9.4. The back bridge
      9.4.1. Semiaxes, bearings and epiploons
      9.4.2. Adjustment axial люфта semiaxes
      9.4.3. A reducer of the back bridge
      9.4.4. An epiploon of a reducer of the back bridge
      9.4.5. Removal and installation of the back bridge
+ 10. A suspension bracket and a steering
+ 11. Brake system
+ 12. A body
+ 13. An electric equipment
+ 14. Electroschemes




ccf2698e

9.4.5. Removal and installation of the back bridge
THE GENERAL DATA

The back bridge with springs
1. Drums
2. Bolts of fastening of a cable manual
Brakes
3. A tip of a cable of a manual brake
4. A hose of brakes
 5. A hose сапуна
6. Карданный a shaft
7. The shock-absorber
8. Step-ladders and the buffer
9. The back bridge

The back bridge with springs and drum-type brakes
N – details are subject to replacement
1. Drums
2. Bolts of fastening of a cable
Manual brake
3. A tip of a cable manual
Brakes
4. A hose of brakes
5. A hose сапуна
6. Карданный a shaft
 7. A stabilizer bolt
Cross-section кстойчивости
8. A longitudinal bar
9. A cross-section bar
10. The bottom fastening of the shock-absorber
11. The back bridge
12. A spring
13. The stabilizer of the cross-section
Stability

The back bridge with springs and disk brakes
N – details are subject to replacement
1. A support
2. A brake disk
3. A bolt of fastening of a cable manual
Brakes (or the gauge of speed)
4. A tip of a cable of a manual brake
5. A hose of brakes
6. A hose сапуна
7. An arm of a spring of the dosing out valve
8. A hose of the blocked differential
9. A socket
10. The gauge of speed
11. Карданный a shaft
12. A bolt of fastening of the stabilizer of cross-section stability
13. A longitudinal bar
14. A cross-section bar
15. The bottom fastening of the shock-absorber
16. The back bridge
17. A spring
18. The stabilizer of cross-section stability
* Is a connection it is definitively tightened after car lowering

THE BRIDGE WITH SPRINGS

PERFORMANCE ORDER
1. Lift the car and establish on supports, having rested them in a frame box.
2. Merge oil from a reducer.
3. Remove wheels and drums.
4. Disconnect a cable of a manual brake, remove a cable guard.
5. Disconnect a hose of a hydrodrive of brakes on a tee.
6. Disconnect a hose сапуна.
7. On a part of cars remove an arm of a spring of the dosing out valve.
8. Put ориентационные labels and disconnect back карданный a shaft.
9. Raise the back bridge for an average part of a beam (or for beam pipes) and disconnect shock-absorbers.
10. Turn away a nut and remove step-ladders with buffers.
11. Turn away a nut, get back earrings and lower back parts of springs.
12. Working together, lower the bridge and get from under the car.
13. Installation is carried out upside-down.
14. Believe a condition of rubber plugs of an earring of a spring, if necessary replace.
15. Correctly сориентируйте a spring earring at assemblage (1 – towards a reducer).
16. Nuts tighten definitively after car lowering. Nuts and bolts tighten according to the demanded moments.
17. Remove air from a hydrodrive of brakes.

THE BRIDGE WITH SPRINGS

PERFORMANCE ORDER
1. Lift the car and establish on supports, having rested them in a frame box.
2. Merge oil from a reducer.
3. Remove wheels.
4. Remove drums (or a support and a brake disk, a support take aside and fix).
5. Disconnect a cable of a manual brake.
6. Disconnect a hose of a hydrodrive of brakes on a tee.
7. Disconnect a hose сапуна.
8. Remove an arm of the dosing out valve of brakes.
9. On cars with the self-blocked differential disconnect a hose and a conducting socket.
10. On cars with ABS-system disconnect the gauge of speed.
11. Put on flanges ориентационные labels and disconnect back карданный a shaft.
12. Turn away a nut of bolts of the stabilizer of cross-section stability, remove draughts of the stabilizer and the plug.
13. Raise the back bridge for an average part of a beam and disconnect longitudinal and cross-section bars.
14. Disconnect the bottom fastenings of shock-absorbers.
15. Lower the bridge, remove the stabilizer and springs.
16. Installation is carried out upside-down.
17. Establish тарельчатые washers on plugs of a bar of the back bridge in the necessary order.
18. Nuts and bolts tighten with following moments: back fastening of a longitudinal bar 122 Н.м. (Drum-type brakes), 216–245 Н.м. (Disk brakes), forward nuts tighten definitively after lowering of the car with the moment 150 Н.м., nuts of a cross-section bar tighten after lowering of the car with the moment 122 Н.м. (For drum-type brakes) and 230 Н.м. (Disk brakes).
19. Nuts of back wheels tighten to the full before car lowering.
20. Other moments of an inhaling look at fig. the Back bridge with springs and drum-type brakes, the Back bridge with springs and disk brakes.
21. Remove air from a hydrodrive of brakes.